Notifications

Clear all

Pro 4 Rules. Who would wanna run this class next season?

Guest · 2007-09-12T20:34:01Z

I edited the BSW Pure stock rules a bit to more of a Pro 4 style, Let me know what you like or what could be changed. Yes its long too. I would also like to know how many people would like to run this class...seriously not just maybe.2008 Pro Stock 4 Division Rules (Possible)1. BODY STYLEOpen to 4-cylinder cars, engines no larger than 2500cc. Cars may be front or rear wheel drive. No mid or rear engine cars. Must have a stock wheelbase as factory listed for that model/year. Racecars must be complete and presentable in appearance at the beginning of each race. No convertibles or open roofs allowed. All holes to be covered with minimum 20 gauge steel.2. BODY APPEARANCEBody must be stock appearing. All chrome moldings, ornaments, door handles, glass or plastic components must be removed except grille, windshield and stock dash. Original rear wheel arches must be retained. Inner trunk panels, hood panels and roof panels must remain stock. (NO GUTTING) No aluminum body panels. Inner door panels may be removed. Tin Spoiler may be used maximum 5". If door skins or fenders are replaced with body they must be stock appearing. Racecars participating in racing events must be presentable in appearance at all times. Cars that are considered improperly prepared may be rejected by the Technical Committee at any event. Racecars must be complete at the beginning of each event. Any cars considered unsafe to driver, competitors, staff or fans will be rejected and not allowed on track. Cars may not be shortened or lengthened in any way.4. BRAKESfour-wheel hydraulic brakes in good working condition are compulsory and are subject to test and inspection. Pedal must be in original position. Four wheel disc brakes are allowed. Drilled and Slotted rotors are allowed.5. BUMPERSBumpers are required. They must be secure and are subject to test. Bumpers must be welded and chained to prevent bumpers from falling off onto the race surface and creating a hazardous condition during a race meet. Homemade bumpers are subject to approval and must be covered with stock bumper covers or aftermarket plastic bumper covers. Ends must be turned in. Sharp edges must be removed or covered. Bumpers must be present and secure at the start of each hear or feature. All cars must be equipped with chains or cables, front and rear, strong enough to be lifted by a tow truck for towing purposes. These must be attached to the chassis and not the bumpers.6. CARBURETION/FUEL INJECTIONCarburetors are open to any 1bbl or 2bbl setup, or factory dual 1bbls. Throttle must have two return springs. May use open element filter.Ram air tubes are allowed, or cold air box. No turbos, blowers or NOS. Fuel injected cars must have a kill switch, marked in red, which shuts off power to the fuel pump. Fuel injected cars must also have a relay, which shuts off power to the fuel pump on low oil pressure or loss of ignition. 7. CHASSIS & SUSPENSIONSSuspension Open, aftermarket struts,shocks,springs allowed.. No devices to raise or lower cars. Adjustable sway bars allowed. Frame must be minumum 4" ride height.Camber is open in Right front and Left front wheels. No rear camber. 8. DOORSMust be welded or bolted securely. Doors may be cut down.9. DRIVELINEMust have steel 360 degree retaining hoop 1/4” by 2” positioned at front and rear of the drive shaft within 6” of each U-joint. (Rear wheel drive only). No chains. Drive shafts must be painted white.10. ENGINEMust be stock for make, model and year. Maximum engine size is 2500cc. No rotary or multi-cam motors allowed. Maximum 3 valves per cylinder. Cams are open to any Lift or Duration. Intake manifold may be port matched and polished, exhaust manifold may be port matched. Maximum overbore .040”. Engine mounts may be made solid. Engines without safety mounts must have a safety chain mounted from engine to frame in case an engine mount breaks.11. EXHAUSTMust exit under floor and behind driver and exit out right or left side of car. Maximum 2 1/2” O.D. pipes. Single exhaust only. Mufflers are mandatory.12. FIRE CONTROLCars must have an approved fire extinguisher mounted in an approved mounting bracket and within driver’s reach with seat belt fastened. Fire extinguisher must have gauge and if the extinguisher is older than three years it must have a recharge slip dated within one year. SFI approved firesuit is mandatory. Stock hood and trunk latches must be removed and replaced with quick entry holddowns.13. FIREWALLS & FLOOROriginal front and rear firewalls must be retained. Floors may be tinned. All holes must be covered with minimum 22 gauge sheet metal either welded or riveted in place. No metal screw allowed.14. FRAMEOn Uni-body cars, front and rear frame sections may be joined for added strength. No X frame supports.15. FUELCars may use street legal unleaded pump gas with no additives allowed or you may use the racing fuel available from Barrie Speedway with no additives allowed. Cars may be disqualified if they ar...

Page 13 / 27 Prev Next

Last Post

RSS

Posts: 0

Silverstone

Sep 14, 2007 7:20 pm

(@Silverstone)

Joined: 1 second ago

I agree, I know alot of people would disagree with me, but how about getting rid of the charger class. Its like watching a consi over and over again!

I'd be all for this class running at Barrie. It would be a blast and very competitive. I agree its time for something new.

Posts: 0

Suby Man

Sep 14, 2007 9:51 pm

(@Suby Man)

Joined: 1 second ago

Me to 8)

Posts: 0

JoeChance

Sep 14, 2007 10:06 pm

(@JoeChance)

Joined: 1 second ago

I would also agree with you Silverstone

Posts: 0

Kahnefreak

Sep 14, 2007 10:45 pm

(@Kahnefreak)

Joined: 1 second ago

I agree, I know alot of people would disagree with me, but how about getting rid of the charger class. Its like watching a consi over and over again!

I think the charger class is great for new drivers to gain experience. I know it may seem that it looks like a consi to people in the "A" division. But it's fun and all of the people in the class are enjoying themselves. Seems kind of funny how there are more charger drivers now then the "A" division! That might say something about the class and the reputation it has! in a couple of years when all the thundercars are new generation, they will just look like a consi to the late models! then what? get rid of the thunders?? i see you guys want a pro 4 class in but that doesn't mean getting rid of a specific class! If anything get rid of the "A" division and make that a pro 4. New drivers have to start somewhere!

Posts: 0

Tooner

Sep 14, 2007 10:46 pm

(@Tooner)

Joined: 1 second ago

The rules are very basic and Tech Official friendly, the car looks very easy to fix and most can build body panels with sheet metal. Sorry I meant for the F4's.

Page 13 / 27 Prev Next

Forum Statistics

95 Forums

25.6 K Topics

91.4 K Posts

12 Online

22 Members

Latest Post: New One Day Saturday Showcase for the Northeast Classic at New Hampshire Motor Speedway Our newest member: racer61 Recent Posts Unread Posts Tags

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed